lithium charge controller
XH-M604 Battery Charger Control Module DC 6-60V Storage Lithium Battery Charging Control Protection Board Switch
How to use:
The factory default starting voltage is 12V, and the stop voltage is 14V.
Connect the battery first (it will not be displayed if the battery is not connected)
Set the start voltage:
Normal display voltage state, press to a starting voltage button ,to display the start charging voltage. long Press the start button 3 seconds, digital flashes, by start and stop button, set the start charging voltage value.
Set Stop voltage:
Normal Voltage normal display mode, press to a Stop voltage button ,to display the Stop charging voltage. long Press the Stop button 3 seconds, digital flashes, by start and stop button, set the Stop charging voltage value.
Setting Error:
Press and hold the start/stop button while power is on, digital display 888, which is the factory setting.
Reference formula:
Charging voltage = rated voltage×0.9, charging current = rated current×0.1, stop voltage = rated voltage × 01.2
NOTE:
When setting the voltage, if it stops at a certain value, it can not be set. You can set another voltage first, and then set this voltage. This is not a circuit and program fault.
Because it is to charge the battery, the positive and negative poles must be connected. If there is any problem that the wiring process cannot be determined or has doubts, you can use a multimeter or other indirect safety method to detect. Do not blindly connect.
Specifications:
Input Voltage: DC 6-60V
Display Accuracy: 0.1V
Control Accuracy: 0.1V
Output Type: direct output
Voltage Tolerance: ±0.1V
Size: 81 x 54 x 24 mm/3.19 x 2.13 x 0.94inch
Application Fields: 6-60V storage battery
3S 20A Lithium Battery 18650 Charger PCB BMS Protection Board 12.6V 18650 Li-ion Battery Cell Charging Module 11.1V 12V 12.6V
3S 20A Lithium Battery 18650 Charger PCB BMS Protection Board 12.6V 18650 Li-ion Battery Cell Charging Module 11.1V 12V 12.6V
Specification:
1. 3 series 12.6V 20A lithium battery protection board (with recovery function -AUTO Recovery)
Application: lithium batteries with a nominal voltage of 3.6V, 3.7V (including 18650, 26650, polymer lithium batteries)
2. Product size: 59 * 20 * 3.4mm
3. Charging voltage: 12.6V-13.0V
4. Continuous discharge current (upper limit): 20A (if the heat dissipation environment is not good, please reduce the load current)
5. Continuous charging current (upper limit): 10A
Note : more than 3A current discharge products rate is more than 3C Ratio calculation formula : 1C rate of the battery , 2000 capacity is equal to 2AH 1 2A maximum working current . 3C ratio battery , 2000 capacity is equal to 2AH * 3 = 6A maximum working current . In use battery heats is ratio is not applicable to , this kind of situatic can't use for a long time , the battery will soon be damaged
Note : don't put the good cells and in bad ! Three groups of battery capacity / internal resistance as close as possible ! ( 2 + 1 good battery , the use effect of poor battery = the use effect of three bad battery )
100A/80A/60A/30A/10A MPPT Auto Solar Charge Controller LCD Display Dual USB Output 5V Solar Panel Battery Charge Regulator
The float voltage is set to: 13.6
The recovery discharge voltage is set to: 12.6
The discharge cut-off voltage is set to: 10.7
12.8 volt lithium iron phosphate battery corresponding
The float voltage is set to: 14.6
The recovery discharge voltage is set to: 13.6
The discharge cut-off voltage is set to: 11.0
11.1 volt lithium battery corresponding
The float voltage is set to: 12.6
The recovery discharge voltage is set to: 11.6
The discharge cut-off voltage is set to: 9.6
The minute is adjustable when the output is turned off, which is more convenient (there is no adjustment when the market is only available).
PV system power Description:
10A/30A /60A/80A/100A battery 12V photovoltaic system: power is respectively 100-1000W
10A/30A /60A/80A/100A battery 24V photovoltaic system: power is respectively 200-2000W
Package Included:
1X Solar Panels Battery Charge Controller
1X User Manual
Notes:
1. The charge regulator is suitable for lead-acid batteries: OPEN, AGM, GEL, nickel hydride, lithium, Liions, or other batteries.
2. This controller can only use photovoltaic panels as charging power. Do not use DC or other power as charging power.
3.The LCD display has an error of 0.2 V- 0.3 V, but this is normal
4. Old batteries may be degraded the capacity after hundereds of cycles, easily drop lower than 8V, which results in the controller will be shut off (LCD screen become totally "DEAD").
5. Indoor u
4S BMS lithium battery 12V LFP4 smart Built-in bluetooth 100a 150a balance Charging and Discharging Over current protection PCM
1. If you need to connect with your mobile phone, you need to buy a BMS with UART communication port or UART/485 dual-communication port,then add a bluetooth module.
2. If you only connect the computer to read data, you need to buy a BMS, then add a UART box or 485 module,
3. If you need to connect both PC and cellphone, please buy the UART/RS485 double-communication BMS, then buy both Bluetooth module and RS485 module
Notice: RS485 Single communication can only connect Upper-computer software, it can not be connected to Bluetooth module and Upper-computer software at same time
60A 50A 40A 30A 20A 10A Solar Charge Controller PWM LED Digital Display 12V24V Automatic Identification Solar Charger Controller
Our controller can be used internary lithium battery, lithium iron phosphate and Lead-acid battery
This controller is a intelligent, multi-purpose solar charge and discharge controller. Fixed LCD display with a very friendly interface is used in this product; various control parameters can be flexibly set, fully meet your various application requirements.
This is NEW Solar Controller ,It can fully meet your home Photovoltaic system(including home lighting system)requirements.It can recognize 12V and 24V Lead acid ,Gel battery, nickel metal hydride, lthium ions , Lifepo4 or other batteriesautomatically.
There are optional 10A 20A 30A model
10A:
if your battery is 12V ,the max solar panel input is 25V 120W
if your battery is 24V ,the max solar panel input is 50V 240W
20A:
if your battery is 12V, the max solar panel input is 25V 240W
if your battery is 24V, the max solar panel input is 50V 480W
30A
if your battery is 12V ,the max solar panel input is 25V 360W
1.Build-in industrial micro controller.
2.Big LCD display,all adjustable parameter.
3.Fully 4-stage PWM charge management.
4.Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection.
60A/50A/40A/30A/20A/10A Solar Charger Controller 12V 24V Auto PWM Controllers LCD Display 5V Dual USB Output Controller
This is NEW Solar Controller ,It can fully meet your home Photovoltaic system(including home lighting system )requirements .It can recongize 12V and 24V Lead acid ,Gel battery automatically
There are optional 10A 20A 30A model
10A:
if your battery is 12V ,the max solar panel input is 25V 120W
if your battery is 24V ,the max solar panel input is 50V 240W
20A:
If your battery is 12V, the max solar panel input is 25V 240W
if your battery is 24V, the max solar panel input is 50V 480W
30A:
if your battery is 12V ,the max solar panel input is 25V 360W
if your battery is 24V ,the max solar panel input is 50V 720W
1.Build-in industrial micro controller.
2.Big LCD display,all adjustable parameter.
3.Fully 4-stage PWM charge management.
4.Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection.
MODEL |
PWM 10A |
PWM 20A |
PWM 30A |
PWM 40A |
PWM 50A |
PWM 60A |
Battery Voltage |
12V 24V Auto |
|||||
Charging Current |
10A |
20A |
30A |
40A |
50A |
60A |
Discharging Current |
10A |
10A |
10A |
20A |
30A |
30A |
Max Solar input |
50V(for 24V battery) 25V(for 12V battery) |
|||||
Equalization |
14.4V(Sealed) 14.2V(Gel) 14.6V(Flood) |
|||||
Float charge |
13.7V(defaul,adjustable) |
|||||
Discharge stop |
10.7V(defaul,adjustable)10.7V(defaul,adjustable) |
|||||
Discharge reconnect |
12.6V(defaul,adjustable) |
|||||
Charge reconnect |
13V |
|||||
Voltage of open light |
Solar Panel 8V(Light lights delay) |
|||||
Voltage of close light |
Solar Panel 8V(Light off delay) |
|||||
USB output |
5V/3A |
|||||
Self-consume |
<10mA |
|||||
Operating temperature |
-35°C~+60°C |
|||||
Size |
133.5*70*35mm |
133.5*70*35mm |
||||
*all red color voltage X2 ,while using 24V system.
54.6V 2A Lithium Battery Charger 48V 18650 21700 10Ah 15Ah 20Ah Lithium Battery Charger For Scooter Electric Bike Battery Charge
54.6V 2A ebike lithium battery charger for 48V 13S lithium battery pack with 3-Pin XLR-M Socket/connector
[Product Specifications]
100% brand new premium super protection.
Type: Lithium Battery Charger
Input: 180-240V AC, 50/60Hz
Output: 54.6V═2A
Weight: 370±3g
Colour: Black
Maximum power: 110W
Connector: XLR-M
Plug: EU / US / AU / UK
Charging indicator: The red light is charging, The green light is full
Safety protection: OVP / OCP / Overload protection / Short circuit protection
Package Included:
1. 54.6V 2A XLR Plug charger *1
2.Power cord *1
The use and maintenance of the charger:
1. When charging, first connect the connector to the battery, and then to the AC; after fully charged, cut off the AC, and then unplug the battery. If the battery plug is first unplugged during charging, especially when the charging current is high (red light), it is easy to damage the charger.
2. When the LED indicator turns green, please continue charging for 2-3 hours.
3. Please try not to charge the charger after the battery is exhausted. Otherwise, the battery will not be protected or even damaged.
4. Please use the charger in a dry place in time.
5. When not using the charger, do not always connect to the power source.
30A 20A 10A 12v 24v Solar charge controller PWM battery charger PV Regulator for Lead acid battery Li-ion lithium batteries
30A 20A 10A 12v 24v Solar charge controller PWM battery charger PV Regulator for Lead acid battery Li-ion lithium batteries
Overview:
This 30A 20A 10A PWM Solar Charge Controller is suitable for 12V 24V lead acid battery,Lithium-ion battery(3 strings of 11.1V lithium batteries);Lithium iron phosphate batteries(4 string of 12.8V).
Features:
1. Build-in industrial micro controller.
2. Big LCD display,all adjustable parameter.
3. Fully 3-stage PWM charge management.
4. Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection.
5.Dual USB 5V output ,max current can be 2.5A
6. Dual mosfet Reverse current protection ,low heat production.
Parameters Table
Iten Pictures:
MPPT Solar Charge Controller 12V 24V 10A 20A 30A 40A 50A Solar Controller Solar Panel Battery Regulator Dual USB 5V LCD Display
Description:
- Advanced maximum power point tracking (MPPT/PWM) technology, the efficiency is not less than 99.5%. High-quality components improve the system performance, and the maximum conversion efficiency is 98%. Super fast tracking speed and guarantee tracking efficiency.
- Large screen LCD display, charge and discharge current display, cumulative power generation and discharge power query, temperature display, light control + delay control; adjustable charge and discharge parameters, with power-off memory and other functions.
- Dual USB output, the maximum current is 2.5A. Equipped with all necessary protection devices, the control parameters of the system are adjustable, easy to set up and operate. Built-in overheating, overcurrent, short circuit, open circuit protection, fault elimination, controller automatic recovery. Two-way MOS tube anti-backflow circuit, high-power charging mode, ultra-low heat.
- Built-in short circuit protection, open circuit protection, reverse connection protection, overload protection. Reverse current protection, low calorific value, with self-recovery function, will not damage the controller.
- Real-time display of temperature, charging current and discharge current. Current autofocus MPPT tracking charging, high charging efficiency, charging process does not stop detection, two-way focus tracking.
Specifications:
Name: LCD screen solar controller
Voltage: DC 12V / 24V
Display: LCD screen
Self-consumption: <10MA
Overcharge protection: 14.4V / 28.8V
Overcharge Float charge: 13.7V / 27.4V
Charge recovery voltage: 12.6V / 25.2V
Over discharge protection: 10.7V / 21.4V
Over discharge recovery: 12.6V / 25.2V
Dual USB output: 5V / 2A (charge mobile phone, iPad, etc.)
Working temperature: -35 ℃ -60 ℃
12V fits 18V solar panel, 24V fits 36V solar panel
12.0 volt lead acid battery corresponding
The float voltage is set to: 13.6
The recovery discharge voltage is set to: 12.6
The discharge cut-off voltage is set to: 10.7
12.8 volt lithium iron phosphate battery corresponding
The float voltage is set to: 14.6
The recovery discharge voltage is set to: 13.6
The discharge cut-off voltage is set to: 11.0
11.1 volt lithium battery corresponding
The float voltage is set to: 12.6
The recovery discharge voltage is set to: 11.6
The discharge cut-off voltage is set to: 9.6
The minute is adjustable when the output is turned off, which is more convenient (there is no adjustment when the market is only available).
PV system power Description:
10A/20A/30A / 40A / 50A/ 60A /70A/80A/90/100A battery 12V photovoltaic system: power is respectively 100-1000W
10A/20A/30A / 40A / 50A/ 60A /70A/80A/90/100A battery 24V photovoltaic system: power is respectively 200-2000W
Package Included:
1X Solar Panels Battery Charge Controller
1X User Manual
Notes:
1. The charge regulator is suitable for lead-acid batteries: OPEN, AGM, GEL, nickel hydride, lithium, Liions, or other batteries.
2. This controller can only use photovoltaic panels as charging power. Do not use DC or other power as charging power.
3.The LCD display has an error of 0.2 V- 0.3 V, but this is normal
4. Old batteries may be degraded the capacity after hundereds of cycles, easily drop lower than 8V, which results in the controller will be shut off (LCD screen become totally “DEAD”).
5. Indoor u
100A/50A/40A/30A/20A/10A 12V 24V Auto Solar Charge Controller MPPT/PWM Controllers LCD Dual USB Output Solar Panel PV Regulator
Only PWM function, please note before purchase
Description:
Feature：
- Advanced maximum power point tracking (MPPT/PWM) technology, the efficiency is not less than 99.5%. High-quality components improve the system performance, and the maximum conversion efficiency is 98%. Super fast tracking speed and guarantee tracking efficiency.
- Large screen LCD display, charge and discharge current display, cumulative power generation and discharge power query, temperature display, light control delay control; adjustable charge and discharge parameters, with power-off memory and other functions.
- Dual USB output, the maximum current is 2.5A. Equipped with all necessary protection devices, the control parameters of the system are adjustable, easy to set up and operate. Built-in overheating, overcurrent, short circuit, open circuit protection, fault elimination, controller automatic recovery. Two-way MOS tube anti-backflow circuit, high-power charging mode, ultra- heat.
- Built-in short circuit protection, open circuit protection, reverse connection protection, overload protection. Reverse current protection, low calorific , with self-recovery function, will not damage the controller.
- Real-time display of temperature, charging current and discharge current. Current autofocus MPPT tracking charging, high charging efficiency, charging process does not stop detection, two-way focus tracking.
Specifications:
Name: LCD screen solar controller
Voltage: DC 12V / 24V
Display: LCD screen
Self-consumption: <10MA
Overcharge protection: 14.4V / 28.8V
Overcharge Float charge: 13.7V / 27.4V
Charge recovery voltage: 12.6V / 25.2V
Over discharge protection: 10.7V / 21.4V
Over discharge recovery: 12.6V / 25.2V
Dual USB output: 5V / 2A (charge mobile phone, iPad, etc.)
Working temperature: -35 ℃ -60 ℃
12V fits 18V solar panel, 24V fits 36V solar panel
12.0 volt lead acid battery corresponding
The float voltage is set to: 13.6
The recovery discharge voltage is set to: 12.6
The discharge cut-off voltage is set to: 10.7
12.8 volt lithium iron phosphate battery corresponding
The float voltage is set to: 14.6
The recovery discharge voltage is set to: 13.6
The discharge cut-off voltage is set to: 11.0
11.1 volt lithium battery corresponding
The float voltage is set to: 12.6
The recovery discharge voltage is set to: 11.6
The discharge cut-off voltage is set to: 9.6
The minute is adjustable when the output is turned off, which is more convenient (there is no adjustment when the market is only available).
PV system power Description:
10A/20A/30A / 40A / 50A/ 60A /70A/80A/90/100A battery 12V photovoltaic system: power is respectively 100-1000W
10A/20A/30A / 40A / 50A/ 60A /70A/80A/90/100A battery 24V photovoltaic system: power is respectively 200-2000W
Package Included:
1X Solar Panels Battery Charge Controller
1X User Manual
Notes:
1. The charge regulator is only suitable for lead-acid batteries: OPEN, AGM, GEL, it is not suited for nickel hydride, lithium, Liions, or other batteries.
2. This controller can only use photovoltaic panels as charging power. Do not use DC or other power as charging power.
3.The LCD display has an error of 0.2 V- 0.3 V, but this is normal
4. Old batteries may be degraded the capacity after hundereds of cycles, easily drop lower than 8V, which results in the controller will be shut off (LCD screen become totally “DEAD”).
5. Indoor use only: the working temperature of this controller is -35°C to 60°C, during hot sunny days, the temperature outside might go up to 60-75°C. Please do keep the controller stay in cool and well-ventilated place to maintain good heat dissipation.
5V 1A USB Micro USB Type C 18650 Lithium Battery Charging Board Charger Controller Module Protection Dual Functions Control New
Protection Micro USB
Mini USB
MINIUSB input terminal with a female, can be directly input to do with the phone charger rechargeable lithium battery, And still retains the input voltage wiring pads, can be very convenient DIY.
It can be used for voltage 3.6 3.7V, etc. 18650, polymer and other lithium battery charge and discharge protection.
Input voltage: 5V
Charging cut-off voltage: 4.2V ± 1%
Maximum charge current: 1000mA
Battery over-discharge protection voltage: 2.5V
Battery overcurrent protection current: 3A
It can be used for charge and discharge protection of 18650, polymer and other lithium batteries with a voltage of 3.6 3. 7V, and single or multiple parallel connections can also be used.
The MINI USB socket and the + - pad next to it are the power input terminals and are connected to 5V.
B+ is connected to the positive electrode of the lithium battery, and B is connected to the negative electrode of the lithium battery.
OUT+ and OUT are connected to the load, such as the positive and negative poles of the moving boost board or other loads.
Connect the battery to B+ B, insert the mobile phone charger to the USB time base, the red light is charging and the green light is full.
Current regulation:
Application range:
The ammeter of the test current can only be connected in series to the 5V input of the charging board.
The charging current is preferably 0.37C of the battery capacity, which is 0.37 times the capacity. For example, the battery charging current of 1000mAH is enough. If the charging speed is too high, the effect will be poor. If the battery voltage is over, it will be more!
The charging connection wire should not be too thin or too long. This connection has a large resistance. If it is too thin, it will be more than the battery voltage.
It is best to have good contact with the battery. Otherwise, the battery voltage will be washed off.
If the input voltage of 5V is high, such as 5.2 or even 5.5, it will cause the charging current to be less than 000om. This is normal. When the voltage is high, the chip will automatically reduce the charging current, and the chip will not burn out. It is normal for the chip to heat up to about 60 degrees in the work. After all, the charging current is large.
Input reverse connection has no effect on the chip, but the output (battery end) will reverse the chip, please pay attention to the buyer.
Protection Mini USB
